- 2 Pallet 80 × 80
- 1 Pallet 360 × 220
- 2 Rail 40 × 20
- 2 Rail 80 × 20
- 2 Rail 120 × 20
- 2 Rail 160 × 20
- 2 Rail 120 × 40
- 2 Rail 180 × 40
- 2 Rail 220 × 40
- 2 Angle plate 180 × 80
- 1 Spindle vise SP 50 AL
- 1 Clamping jaws with receiver pins
- 1 Clamping block for pallet
- 1 Clamping chuck AL (3-jaw chuck, Ø125)
- 1 Spannhand 25
- 1 Clamping hand 50
- 4 Clamping spring element
- 2 Clamping spring unit
- 2 Clamping claw unit
- 2 Receiver joint M6
- 5 Connector Ø20 IM6-IM10
- 2 Stud bolt Ø16 × 30
- 2 Stud bolt Ø16 × 40
- 2 Stud bolt Ø16 × 60
- 2 Stud bolt Ø16 × 80
- 2 Stud bolt Ø16 × 100
- 5 Center ring Ø10 - 22 × 5
- 5 Center ring Ø10 - 18 × 5
- 2 Stud bolt Ø20 × 30
- 2 Stud bolt Ø20 × 40
- 2 Stud bolt Ø20 × 60
- 2 Stud bolt Ø20 × 80
- 2 Stud bolt Ø20 × 100
- 5 Slide rail (suitable for knurled-screw M6 / M7)
- 4 Receiver - M10 × 1 L=24 mm
- 4 Receiver - M10 × 1 L=34 mm
- 4 Receiver - M10 × 1 L=54 mm
- 2 Supporting plate Ø20 × 28
- 2 Supporting plate Ø20 × 38
- 2 Supporting plate Ø20 × 58
- 2 Supporting pin - M10 × 1 - 50 × 35
- 2 Supporting pin - M10 × 1 - 75 × 50
- 2 Supporting pin X-stop - M10 × 1
- 2 Supporting pin XY-stop - M10 × 1
- 1 Ball joint M6 - M10 × 1
- 1 Center Ø30 × 45
- 2 Center Ø16 × 33
- 5 Receiver M6
- 2 Prism support Ø6 - 16
- 2 Prism support Ø10 - 22
- 2 Prism 120° - M10 × 1
- 2 Spring holder for prism 120° - M10 × 1
- 2 Fixed stop M10 × 36
- 2 Fixed stop M10 × 56
- 3 Supporting bolt
- 3 Stop pin
- 2 Supporting prism Ø100 (suitable for pallet)
- 2 Prism element 20 × 20 × 30
- 2 Prism element 20 × 40 × 45
- 2 Clamping claw 80
- 2 Clamping claw 60
- 1 Clamping springs, set
- 1 Base plate 135 × 100 × 12
- 2 Locating screw M7
- 30 Centering sleeve Ø10 × 8
- 2 Knurled screw M6 × 35
- 2 Knurled screw M6 × 45
- 2 Knurled screw M6 × 55
- 5 Knurled screw M7 × 25
- 2 Supporting screw M6 × 35
- 5 Slotted nut
- 10 Plastic plain washer Ø16 × 6 × 4
- 10 Plastic plain washer Ø16 × 6 × 4
- 10 Plastic plain washer Ø20 × 10 × 2
- 10 Plastic plain washer Ø20 × 10 × 4
- 10 Plastic plain washer Ø16 × 6 × 2
- 10 Knurled nut
- 4 Hold down clamp L=60
- 4 Receiver pin M6 for hold down clamp
- 2 Toggle clamp HS
- 20 Threaded pin M6 × 25
- 20 Threaded pin M10 × 25
- 10 Cap screw M6 × 12
- 10 Cap screw M6 × 16
- 20 Cap screw M6 × 20
- 20 Cap screw M6 × 25
- 10 Cap screw M6 × 35
- 1 Tool kit
- 1 Plastic case
ALUMESS.maxx Starter kit C
The Alumess system is mainly designed for univer sal and flexible use on tactile coordinate measuring machines (CMMs). Further areas of use are for the production of samples and prototypes, laser inscription, laser proces sing or as a mounting device.
Position holes and mounting threads in the pallets, plates, rails and angle plates as well as a wide range of support, positioning and stop elements enable a reproducible const ruction of any clamping fixture.
Maximum reproducibility of the fixture allows that only the specific constructed and produ ced elements must be stored for re-use as required.
Any questions?
Request CAD data or ask a question about the product- Order number: B500100003
Choose version
| Version | Order Number | Pieces |
| ALUMESS.maxx C | B500100003 | 389 |
Viewed